SBBR反应器中耐冷微生物的驯化与识别

以模拟生活污水为处理对象，三种不同填料为生物膜载体，运行 A、B、C三个SBBR，通过逐步降温（25、20、15、10、6和5℃）培养驯化处理低温污水的生物膜。运行251周期，三个反应器COD出水浓度均低于50 mg/L；B反应器对氨氮去除效果优于A和C。特别在低温5℃时，A、B和C三个反应器氨氮平均出水浓度分别为14.1、3.79和14.1 mg/L。高通量测序结果显示，5℃时，三个反应器中均以降解有机物的微生物为主；只有B反应器中驯化富集出了嗜冷硝化菌（Candidatus Nitrotoga）；而其他有硝化作用的菌属在B反应器中的丰度也高于A和C反应器；不利于脱氮的类固氮菌（Elstera）在A和C反应器中丰度较高。此结果可从微生物角度解释三个反应器处理效果的差异性，表明B反应器处理低温污水有显著优势，其所用填料可结合低温菌进一步开发利用。     

125I粒子条联合胆道支架植入治疗恶性梗阻性黄疸22例疗效分析

【摘要】　 　目的 研究和探讨125I粒子条联合胆道支架植入治疗恶性梗阻性黄疸的临床疗效。方法 2011年6月—2013年9月收治恶性梗阻性黄疸患者40例。行胆道支架植入术治疗患者18例，为对照组；采用125I粒子条联合胆道支架植入患者22例，为观察组。两组均采用经皮肝穿刺胆道引流（PTCD）并胆道支架植入。结果 观察组与对照组的平均胆道开通时间分别为（8.7 ± 0.7）和（6.2 ± 0.4）个月，两组比较差异有统计学意义（P < 0.05）。观察组与对照组术后平均生存时间分别为（11.4 ± 0.8）和（8.7 ± 0.5）个月，生存时间的差异有统计学意义（P < 0.05）。术后近期疗效及并发症两组之间的比较无明显差异（P > 0.05），但是远期疗效有显著差异（P < 0.05）。结论 与对照组相比，观察组的术后生存时间及胆道开通时间明显延长，对于125I粒子条联合支架治疗恶性梗阻性黄疸值得进一步临床研究。
     

Fine-grained cooperative access control scheme with hidden policies

The traditional ciphertext policy attribute-based encryption (CP-ABE) has two problems:one is that the access policy must be embedded in the ciphertext and sent, which leads to the disclosure of user爷 s privacy information, the other is that it does not support collaborative decryption, which cannot meet the actual demand of conditional collaborative decryption among multiple users. In order to deal with the above two problems at the same time, a fine-grained cooperative access control scheme with hidden policies (FCAC-HP) is proposed based on the existing CP-ABE schemes combined with blockchain technology. In FCAC-HP scheme, users are grouped by group identifier so that only users within the same group can cooperate. In the data encryption stage, the access policy is encrypted and then embedded in the ciphertext to protect the privacy information of the access policy. In the data access stage, the anonymous attribute matching technology is introduced so that only matched users can decrypt ciphertext data to improve the efficiency of the system. In this process, a smart contract is used to execute the verification algorithm to ensure the credibility of the results. In terms of security, FCAC-HP scheme is based on the prime subgroup discriminative assumption and is proved to be indistinguishable under chosen plaintext attack (CPA) by dual system encryption technology. Experimental verification and analysis show that FCAC-HP scheme improves computational efficiency while implementing complex functions.     

碳酸盐岩岩溶储层多井评价方法及地质应用

多井评价是建立在单井精细解释对比分析基础上的预测储层及含油气性平面分布规律的技术方法,而常规测井资料无法区分碳酸盐岩岩溶储层,因而利用多井评价结果确定岩溶发育程度在平面上的分布规律就显得十分重要。为此,在岩心标定成像测井的基础上,对四川盆地高石梯—磨溪地区15口井的成像测井岩溶发育特征进行分析,建立了中二叠统茅口组岩溶发育各分带的标准成像图版,利用交会图及直方图分析各分带的常规测井响应特征,在此基础上形成了电成像测井刻度常规测井识别岩溶发育带的新方法。研究结果表明:①高石梯—磨溪地区茅口组岩溶带自上而下可划分为风化壳残积带、垂直渗流岩溶带、水平潜流岩溶带以及受岩溶作用较弱的基岩;②风化壳残积带在成像测井图像显示为"暗—亮—暗"条带状模式,垂直渗流岩溶带为垂直线状与暗色斑状组合模式,水平潜流岩溶带为水平线状—层状与斑状组合模式,基岩整体显示为亮色块状模式偶见线状或斑状特征;③有效储层主要发育在垂直渗流带和水平潜流带的顶部;④该区茅口组岩溶发育主要受裂缝发育控制,而裂缝发育又与断层关系密切。结论认为,该新方法对碳酸盐岩岩溶储层的多井评价具有普遍适用性,为四川盆地中二叠统风险探井的部署提供了技术支撑。     

Spreading and Curing Behaviors of a Thermosetting Droplet-Silicone on a Heated Surface

Thermosetting materials are widely used as encapsulation in the electrical packaging to protect the core electronic components from external force, moisture, dust, and other factors. However, the spreading and curing behaviors of such kind of fluid on a heated surface have been rarely explored. In this study, we experimentally and numerically investigated the spreading and curing behaviors of the silicone(OE6550 A/B, which is widely used in the light-emitting diode packaging) droplet with diameter of ～2.2 mm on a heated surface with temperature ranging from 25 ℃ to 250 ℃. For the experiments, we established a setup with high-speed camera and heating unit to capture the fast spreading process of the silicone droplet on the heated surface. For the numerical simulation, we built a viscosity model of the silicone by using the Kiuna's model and combined the viscosity model with the Volume of Fluid(VOF) model by the User Defined Function(UDF) method. The results show that the surface temperature significantly affected the spreading behaviors of the silicone droplet since it determines the temperature and viscosity distribution inside the droplet. For surface temperature varied from 25 ℃ to 250 ℃, the final contact radius changed from ～2.95 mm to ～1.78 mm and the total spreading time changed from ～511 s to ～0.15 s. By further analyzing the viscosity evolution of the droplet, we found that the decreasing of the total spreading time was caused by the decrease of the viscosity under high surface temperature at initial spreading stage, while the reduction of the final contact radius was caused by the curing of the precursor film. This study supplies a strategy to tuning the spreading and curing behavior of silicone by imposing high surface temperature, which is of great importance to the electronic packaging.     

Improved Corrosion Resistance of Selective Laser Melted Ti–5Cu Alloy Using Atomized Ti–5Cu Powder

The different types of metal powder used for selective laser melting(SLM) process would cause distinct corrosion behavior due to the uniformity of the obtained microstructure.The SLM-produced Ti–5Cu alloy using atomized Ti–5Cu metal powder(SLMed Ti–5Cu) in this work reveals a relatively uniform microstructure with overwhelming acicular α/α′ phase and shows great advantages on corrosion resistance compared with the SLM-produced Ti–5Cu alloy using the mixture powder(SLMedM Ti–5Cu).The effect of the micro-galvanic cells decreases due to the undetectable Ti_2Cu phase in the microstructure of the SLMed Ti–5Cu.An apparent passivation behavior was observed for SLMed Ti–5Cu instead of severe pitting phenomenon for the SLMed-M Ti–5Cu.The charge transfer resistance of SLMed Ti–5Cu in this work is 10.09 ± 2.63 MΩ cm~2, which is significantly higher than that of SLMed-M Ti–5Cu(4.76 MΩ cm~2).The above result indicates the atomized Ti–5Cu powder plays an important role in the formation of the uniform microstructure of SLMed product, thereby enhancing its corrosion resistance in Hank's solution at 37 ℃.     

基于(火用)效率目标的环冷机余热回收系统操作参数优化

摘要：针对烧结环冷机余热回收利用率不高的难题，采用分析法建立了评价某钢铁厂烧结环冷机余热回收系统运行效率的效率模型。基于多孔介质模型、局部非热平衡方程、真实气体SRK方程建立环冷机内气固两相换热模型。通过CFD仿真模拟，探究料层高度、循环风机输入烟气温度、烧结矿底部入口风速三项可控环冷机运行工艺参数对系统效率的影响规律。结果表明，料层厚度在1～1.5 m区间每增加0.1 m，效率增加0.8%～1.1%；循环风温在100～140℃之间每增加10℃，效率增加1.4%～1.5%；烧结矿底部入口风速在0.9～1.9 m/s之间每增加0.1 m/s，效率降低0.18%～0.24%。在此基础上，基于工业运行数据建立效率正交试验优化模型，提高了该余热回收系统3.42%的效率。